上海埃飞科技
Worldwide Technology(S. H)
上海埃飞科技
Worldwide Technology(S. H)产品展示
Perovskite battery cycle exposure test system
The perovskite battery cycle exposure test system can simulate the damage caused by full-spectrum sunlight, test temperature and humidity changes, and can reproduce the aging effect of months or even years outdoors in a few days or weeks.
The perovskite battery cycle exposure test system can simulate the damage caused by full-spectrum sunlight, test temperature and humidity changes, and can reproduce the aging effect of months or even years outdoors in a few days or weeks. It can provide corresponding environmental simulation and accelerated tests for scientific research, product development and quality control.
Product features and advantages:
1. Very simple operation interface, quick results
2. Using a unique light intensity feedback system, with excellent light intensity stability (within ±2%), the temperature range is 20 to 90°C
3. The temperature accuracy can be within the range of ±1°C and within the range of 20 to 90°C. The range of ±0.5°C is 25 to 60°C.
4. The constant temperature room is equipped with a BNC connector for constant temperature I-V measurement
5. The observation window can observe the sample constant temperature chamber without opening the door.
6. It can realize double 85 test, 85% humidity and 85℃ long-term aging test.
7. It can achieve 15000 hours of long-term testing without changing the light source
8. The bottom of the aging chamber is designed with a drainage groove to prevent steam condensation and maximize the protection of the test workpiece.
Product specifications:
one. Configuration
(1) Light source part
(2) Optical system
(3) Constant temperature room
(4) Measuring system
(IV curve graph)
two. Specification
(1) Light source part
① Use 200W high-brightness LED light source.
② Air-cooled and water-cooled dual cooling systems using adjustable fans.
③The system is equipped with a safe and adjustable DC power supply.
④The power supply adopts constant lighting LED light source, which has long life and stable light intensity.
(2) Optical system
①Multiple LED lamp beads, uniform intensity of illumination area.
②The irradiation area should be 300 mm×300 mm.
③The focal length at the exit of the exit condenser system should be 110-220mm or more.
④The height of the optical axis should be 50-140mm.
(Double 85 test)
(3) Constant temperature room
①The set temperature range is 20 to 90°C.
②The temperature accuracy should be within the range of ±1°C and within the range of 20 to 90°C. Within ±0.5°C
The range is 25 to 60°C.
③The temperature should be controlled by digital microcomputer PID control.
④The temperature sensor should use K-type thermocouple.
⑤The humidity measurement range should be 0 to 85% RH.
⑥The humidity measurement accuracy should be ±2% (25°C, 0 to 80%RH).
⑦The BNC connector panel is built in the constant temperature room.
⑧The observation window can observe the sample constant temperature chamber without opening the door.
⑨The sample rack/support should be used as standard configuration.
(Temperature and humidity controllable range diagram, no active humidity and heat load)
(4) Measuring system
①Equipped with 16 sample switching relay boxes, 16 samples can be switched.
②In the four sample switching relay boxes, when no samples are measured, three types of open circuit, short circuit or load resistance can be selected for each sample.
③For each of the 16 samples, the load resistance of the 4-sample switch relay box should be able to continuously change from 0 to 2000Ω.
④ A current and voltmeter should be installed. The current measurement range is ±10 pA to 1 A or higher, and the voltage application range is ±1μV to 20 V or higher.
⑤ Time course I-V measurement software should be provided. Up to 1000 hours (60,000 minutes), the minimum 1 minute step can be arbitrarily input IV measurement and short-circuit current measurement.
⑥ The sample name and sample area of the 16 samples can be entered separately in the time course I-V measurement software.
⑦The I-V measurement software should be able to measure short-circuit current density, open circuit voltage, maximum output, maximum power supply voltage, maximum power current, fill factor (FF), conversion efficiency, series resistance, parallel resistance and the set time interval.
⑧The time course I-V measurement software can save the measurement data in the text in real time during the time course measurement, and can create an EXCEL file after the measurement is completed.
⑨The timetable I-V measurement software should be in English.
⑩A set of Note PC with Windows 10 should be provided.
Classic users:
More than a dozen domestic research groups such as Shanghai Jiaotong University, Peking University, Chinese Academy of Sciences, and Shanghai Institute of Ceramics.
因用于机器人各方面应用且与大多数机器人类型兼容，AutoCal系统可以检测出机器人自身构造和工具中心点（TCP）的 突然改变或偏离，并且该系统无需人为干涉就自动地更正这些误差。
AutoCal系统-Dynalog的先进水平校准技术，Dynalog是机器人单元标定技术的世界领导者。它的主流产品DynaCal 系统，被应用于离线的机器人单元校准，并作为最精确的和技术先进的机器人校准程序为许多机器人制造商和终端使用者所接受。AutoCal 系统将已证实的DynaCal校准技术结合到一个在线的全自动系统中，该系统专为程序控制和复原而设计的，价格低廉。
AutoCal系统提供在线的机器人校准方案，旨在快速和自动地保证机械设备的工作性能。因用于机器人各方面应用且与大多数机器人类型兼容，AutoCal系统可以检测出机器人自身构造和工具中心点（TCP）的 突然改变或偏离，并且该系统无需人为干涉就自动地更正这些误差。这意味着不用猜测哪里会出错，不用浪费宝贵时间在机器人程序重复校准上，产品品质无任何损失。
AutoCal系统-Dynalog的先进水平校准技术，Dynalog是机器人单元标定技术的世界领导者。它的主流产品DynaCal 系统，被应用于离线的机器人单元校准，并作为最精确的和技术先进的机器人校准程序为许多机器人制造商和终端使用者所接受。AutoCal 系统将已证实的DynaCal校准技术结合到一个在线的全自动系统中，该系统专为程序控制和复原而设计的，价格低廉。