NV-CENTRE CONFOCAL MICROSCOPY

• 详细介绍
• 详细参数

• 详细介绍

  NV-CENTRE CONFOCAL MICROSCOPY
  Low Temperature Microscope
  LT-SCM works by passing a laser beam through a light source aperture which is focused by an objective lens into a small area on the surface of the sample and an image is built up pixel-by-pixel by collecting the emitted photons from sample surface.
  LT-SCM works by passing a laser beam through a light source aperture which is focused by an objective lens into a small area on the surface of the sample and an image is built up pixel-by-pixel by collecting the emitted photons from sample surface. LT-SCM provides a high-resolution image with all areas in focus throughout the field of view, even for a sample having dents and protrusions on the surface. It enables the non-contact and non-destructive measurements at variable temperatures.
  Product Specifications
  High NA APO Objective, 0.82NA / 0.95mm
  532nm, SLM 10mW Laser
  30x30x15μm Scan area @4K
  49mm Outer Diameter
  10mK to 300K temperature range
  APD for optical detection
  8 pin connections for experiments
  6x6x12mm Range XYZ Sample Nanopositioner
  4x4x6mm Range XYZ Nanopositioner for NV/QTF Sensor
  200nm resolution resistive position sensors
  State of the Art Ultra Low Noise FPGA Based
  AFM Controller with High speed USB interface
  32 Bit Real time Processor with 128MB DDR SDRAM
  2 Channel 16Bit/100MHz ADC
  2 Channel 16Bit/100MHz DAC
  7 Digital PID Loops on FPGA
  19 Channel Piezo Nanopositioner Controller
  16 Channel 24Bit/175kHz ADC
  24 Bit DACs for XYZ Scan Signals
  Low Noise High Voltage Amplifiers
  
  
  

• 详细参数

• 产品特色

  因用于机器人各方面应用且与大多数机器人类型兼容，AutoCal系统可以检测出机器人自身构造和工具中心点（TCP）的 突然改变或偏离，并且该系统无需人为干涉就自动地更正这些误差。

  AutoCal系统-Dynalog的先进水平校准技术，Dynalog是机器人单元标定技术的世界领导者。它的主流产品DynaCal 系统，被应用于离线的机器人单元校准，并作为最精确的和技术先进的机器人校准程序为许多机器人制造商和终端使用者所接受。AutoCal 系统将已证实的DynaCal校准技术结合到一个在线的全自动系统中，该系统专为程序控制和复原而设计的，价格低廉。

• 详细介绍

  AutoCal系统提供在线的机器人校准方案，旨在快速和自动地保证机械设备的工作性能。因用于机器人各方面应用且与大多数机器人类型兼容，AutoCal系统可以检测出机器人自身构造和工具中心点（TCP）的 突然改变或偏离，并且该系统无需人为干涉就自动地更正这些误差。这意味着不用猜测哪里会出错，不用浪费宝贵时间在机器人程序重复校准上，产品品质无任何损失。

  AutoCal系统-Dynalog的先进水平校准技术，Dynalog是机器人单元标定技术的世界领导者。它的主流产品DynaCal 系统，被应用于离线的机器人单元校准，并作为最精确的和技术先进的机器人校准程序为许多机器人制造商和终端使用者所接受。AutoCal 系统将已证实的DynaCal校准技术结合到一个在线的全自动系统中，该系统专为程序控制和复原而设计的，价格低廉。